Category: Resistance Instruments

Resistance Instruments

  • 15kV Insulation Resistance meter MIC15k1 - Sonel

    15kV Insulation Resistance meter | MIC15k1

    Call for price

    Bluetooth labelIP67 LabelIP40 Label

    15kV Insulation Resistance meter MIC15k1 Overview

    The MIC-15k1 meter is designed to measure the insulation resistance of power objects, i.e. single- and multicore cables, transformers, motors and generators, capacitors, switches, and other devices installed in power stations. It is especially recommended for measurements in areas with very high electromagnetic disturbances, e.g. electrical substations with 1200 kV AC and 500 kV DC. Thanks to the 15 kV measuring voltage (in accordance with ANSI / NETA ATS-2009 TABLES 100.1) the meter can be used for measuring objects with a nominal voltage above 34.5 kV.

    15kV Insulation Resistance meter MIC15k1 Features

    • Diagnostics of insulation systems based on standard measurements of IR, DAR, PI, SV, RT, DD, widened with the partial discharge (PD) indicator for every each of these measurements.
    • It allows testing the electrical durability of the tested object - breakdown voltage indication.
    • High resistance to electromagnetic interferences guarantees uninterrupted work in power stations and close to high voltage transmission lines up to 1200 kV AC and 500 kV DC.
    • The function of smooth voltage rise in time (RT - Ramp Test) allows to state the partial discharges in the facility and to carry out a partial location of their occurrence.
    • Efficient converter with a power of ~150 W that enables insulation burnout, allowing for pinpointing the location of cables and wires short circuit using one of the following:
      • visual method (if power cables are visible along the entire length),
      • reflectometric methods, seismic-acoustic waves detector, or with A-frame to indicate the direction of the fault (the conductor must be buried in the ground with earth direct contact).
    • Compatible with external software.

    Datasheet

  • Sheet Metal Surface Quality MRP 29 HY Schuetz Messtechnik

    Sheet Metal Surface Quality Tester | MRP29HY

    Call for price

    Sheet Metal Surface Quality Tester MRP29HY Overview

    The Sheet Metal Surface Quality Tester MRP29HY can measure surface quality and the efficiency in surface conditions of sheet micro-ohmmeter metals/plates. The MRP29HY consists of a micro-ohmmeter and a hydraulic press and the engineering principle is based on the ‘German Association for Welding Technology E.V.’ data sheet for quality evaluation on the sheet metal which is vital for every application, where the reliability is dependent on the surface quality. The priority is the welding of sheet metal (e.g. after etching, and brushing) in the automotive and aircraft industry, but also surface treatment (e.g. lacquer and splicing). The MRP29HY can measure the contact resistance on single sheet metal or overlap sheet metal e.g. aluminum or corresponding alloy, and other materials.

    Datasheet

  • Transimpedance Amplifier TA107 - Newton4th Ltd

    Transimpedance Amplifier High Impedance Measurement | TA107

    Call for price

    Transimpedance Amplifier High Impedance Measurement TA107 Overview

    The TA107 Transimpedance Amplifier provides a solution for high impedance analysis applications by measuring the current flowing through a component or material under test with an innovative earth-referenced transimpedance amplifier technique. The TA107 Transimpedance Amplifier supplements our existing impedance analyzer range to provide a solution for a wide range of measurement applications.

    Transimpedance Amplifier High Impedance Measurement TA107 Features

    • 1MΩ to 100GΩ range with PSM1735
    • DC to 100kHz Frequency range
    • Adaptor or direct PSM power
    • Simple connection and operation

    Datasheet

  • Multi-function electrical meter

    Electrical Installation Meter with Power Analyzer | MPI-540

    Call for price

    Safety Rating CAT III at 500V LabelSafety Rating Cat IV at 300V labelLi-Ion Battery labelIP51 LabelBluetooth labelWiFi label

    Electrical Installation  Meter with Power Analyzer MPI-540 Overview

    The MPI-540 meter is designed for checking industrial and home electrical installations. The measurements taken by the device, determine the safety of the installation. In addition, the user has the possibility to register the parameters of electrical networks located at these facilities. This allows for the measurement of the parameters of protection against electric shock using a single universal device while verifying the quality of electricity. The Auto mode allows significant automation of measurements of the meter and makes it possible to test the functioning of residual current circuit breakers, as well as in pre-programmed measuring sequences, which can be extended with their own sequences. Automatic measurement of insulation resistance of 3-, 4- and 5-wire conductors are possible by using an additional AUTO ISO-1000C adapter.

    Datasheet

  • Mega Ohm meter | MIC-10

    R6,712.00

    Safety Rating Cat IV at 600V label Safety Rating Cat III at 1000V labelIngress protection IP67 label

    Mega Ohm meter MIC-10  Overview

    MIC-10 meter is designed to perform electrical tests, which establishes the safety of insulation in a systems. This is a very handy digital multimeter tool,  measuring Insulation resistance up to 10GOhms with up to 1000V measuring in accordance with IEC61557-2.

    Mega Ohm meter Mic-10 Features

    • continuous indication of insulation resistance or leakage current,
    • select test voltages of: 50, 100, 250, 500, 1000 V,
    • automatic discharge of capacitance of tested object after the insulation resistance measurement,
    • acoustic signalling of five-second periods to facilitate obtaining time characteristics,
    • indication of actual test voltage during the measurement,
    • protection against measuring live objects,
    • three-lead measurement.
    • Continuity measurement of protective and equipotential conductors according to EN 61557 - 4 with  >200 mA current
    • Low-voltage circuit continuity and resistance measurement:
    • circuit resistance measurement (<1999 ) with the <15 mA current,
    • quick sound signal if circuit resistance is below 30Ω.
    • Capacitance measurement during the RISO measurement
    • Measurement of alternating and direct voltages in the 0...600 V range.
    • Power supply: 4 AA disposable or rechargeable batteries, monitoring of power supply voltage.
    • Meter conform to EN 61557.
  • Profile picture of Earth Resistance meter.

    Earth Resistance Meter MRU-10

    R8,022.00

    Safety Rating Cat IV at 150V labelIngress protection IP67 label

    Overview of MRU-10 Earth Resistance Meter

    The Sonel MRU-10 is a simple meter that allows you to measure earthing resistance using a technical method as well as measure grounding resistance using the pole method. The instruments is easy to handle, resistive to interference, and highly accurate. This unit allows checking the quality of the grounding system on the basics of the received measurement result. The device is simple to operate and intuitive and an excellent choice for electrical  technicians, installations contractors and professionals dealing with grounding measurements. This Earth Resistance meter is durable with firm housing, as well as big and clear display with ergonomic design makes this instrument ideal to use both in the field and most working environments.

    Earth Resistance Meter features

    • measure earthing resistance using auxiliary electrodes method 2-pole and 3-pole
    • measurement of resistance of auxiliary electrodes RS and RH,
    • measurement in the presence of interference voltage in the power network with frequency 50 Hz and 60 Hz,
    • selection of maximum measuring voltage (25 V and 50 V),
    • measurement category: CAT IV 150 V acc. to EN 61010-1,
    • protection class acc. to EN 60529: IP67.
    • indication of battery state.
    • LCD display: segment, backlit,
    • number of measurements (RE3P) carried out of set of batteries: > 3000

     

  • Profile Picture Earth Resistance & Resistivity Meter

    Earth Resistance Meter | MRU-200 GPS

    Call for price

    Safety Rating Cat IV at 300V label Safety Rating Cat III at 600V label Bluetooth Enabled label GPS

    Overview of  MRU-200 Earth Resistance meter

    The MRU-200 earth resistance meter is a unique meter in the market, which uses all measurement methods to get earth resistance.  Making sure the ground system has a low earth ground resistance when initially installed is a very important safety check, but making sure the  low resistance is maintain is just as important. Resistance of grounding system might increase when the ground rods are corroded. Over time soil with high moisture, salt content and high temperatures will corrode connections.  It is therefor recommended that the earthing be checked periodically to make sure there is not an big increase in resistance.

    Earth Resistance Meter Features:

    • earth resistance measurement with 2-pole, 3-pole,4-pole method,
    • two clamps earth resistance measurement without auxiliary test probes,
    • impulse earth impedance measurement, three kinds of measuring impulse 4/10μs, 8/20μs, 10/350μs,
    • earth resistance measurement without disconnecting measured earths (using clamp),
    • earth resistivity measurement,
    • continuity measurement,
    • leakage current measurement.
    • optional built in GPS,
    • GPS coordinates of the measurement are stored in meter memory (with GPS model)
    • measurement of resistance of auxiliary electrodes RS and RH,
    • measurement of interference voltage,
    • measurement of interference frequency,
    • measurement in the presence of interference voltage in the power network
    • with frequency 16 2/3 Hz, 50 Hz, 60 Hz and 400 Hz (with automatic selection of proper frequency of measuring signal or with
    • anual selection),
    • selection of maximum measuring voltage (25 V and 50 V)
    • introducing the distance between the electrodes for the resistivity in metres (m) and feet (ft),
    • memory of 990 measurements (10 banks of 99 cells each),
    • calibration of clamp used,
    • real time clock (RTC),
    • data transmission to the computer USB and Bluetooth*,
    • indication of battery state.
  • Standard Programmable Resistor SRP-10G0-10T0

    Call for price

    Overview of the Standard Programmable Resistor SRP-10G0-10T0

    The SRP-10G0-10T0 calibrator, which has a range from 10GΩ to 10TΩ,  is a source of high resistance used as a standard in calibration and test of analogue and digital insulation resistance meters. The selected resistance can be maintained for a long time under external direct voltage up to 10 000 V, provided that the current in the measuring circuit does not exceed 3 mA. The required resistance is set by the user using the calibrator's touch keypad or via an external PC application. The required value is set automatically thanks to the switching of a precise resistance matrix. The controlling processor calculates the required combination of resistors, ensuring adequate resistance precision.

  • Impedance Loop Meter Angle view

    Loop Impedance Meter MZC-304

    R10,150.00

    Safety Rating Cat IV at 300V label  Safety Rating Cat III at 600V label  Ingress protection IP67 label

    Loop Impedance Meter MZC-304

    The MZC-304 meter is designed for testing the protection against electric shock in the mains systems. The meter is used to make measurements which results determine the electrical installation safety level.

    Loop Impedance Meter Features MZC-304

    • Measurements of impedance in a short circuit loop.
      • L-PE circuit,
      • L-N, L-L circuit
      • L-PE(RCD) circuit - without tripping the circuit breaker  ≥ 30 mA.
    • Low voltage resistance measurement:
    • Continuity measurement - DC current +200 mA with wire resistivity rest
    • Low current resistance measurement with acoustic signalling,
    • The measurements are possible in installations 220/30 V, 240/415 V with frequency range 45...65 Hz.
    • Memory of 10 banks of 99 cells each (min. 10000 records).
    • Radio wireless interface communication
  • 10kV Insulation Resistance meter up to 40 Tera-Ohm | MIC10k1

    Call for price

    IEC 61557 label Safety Cat IV at 600V label Safety Cat III at 1000V label Bluetooth Enabled label Ingress protection IP40 label

     

    Megohmmeter - 10kV up to 40 Tera Ohms MIC 10k

    This insulation resistance meter has digital filters function for measurements in high noise environment.  Continuity measurement of protective connections and equipotential bonding in accordance with EN 61557-4 with current > 200 mA.  Adjustable limits for measured resistance RISO and RCONT. Measurement of leakage current during insulation resistance testing. DC and AC voltage measurement in the range of  0...750 V. Drawing graphs on the display during measurement. Innovative  memory  with possibility of description of:  measurement points,  facilities,  names  of  customers. Operating with mini Bluetooth keyboard (option). MIC-10s1 - Stable measurements in noisy environments such as 765 kV substations. Graphic LCD 5,6'’ backlit. Keyboard backlit. Power supply from battery packs. Built-in fast charger. The instruments meet the requirements of the EN 61557 standard.

    10 kV Insulation Resistance Meter Features

    • clear visible display
    • measurement voltage any in the range of: 50…10000 V (50...1000 V at 10 V and 1...10 kV at 25 V),
    • continuous indication of measured insulation resistance or leakage current,
    • automatic discharge of measured object capacitance voltage after the end of insulation resistance measurement,
    • acoustic signaling of 5 seconds intervals to facilitate capturing time characteristics,
    • adjustable measuring time to 99'59'’,
    • metered T1, T2 and T3 test times for measuring one or two absorption coefficients from the range of 1…600 s,
    • polarization index (PI), absorption coefficients Ab1, Ab2 and dielectric absorption ratio (DAR) measurement,
    • indication of actual test voltage during measurement,
    • 1.2 mA, 3 mA and 5 mA test current,
    • insulation resistance measurement using two- or three-wire method,
    • measurements with test leads up to 20 m...
    • protection against measuring live objects,
    • automatic measurement of multiple core cables with the additional AutoISO-5000 adapter (for MIC-10k1 max. voltage 5 kV)
    • measurement of capacitance during the measurement of RISO.
    • measurement of temperature (with additional probe - WASONT1),
    • step voltage insulation resistance measurement (SV),
    • Dielectric Discharge calculation (DD),
    • location of damage (burnout),
  • Short Circuit Loop Impedance Meter MZC-305

    Call for price

    Safety Rating Cat IV at 600V labelSafety Rating Cat III at 1000V label

    Short Circuit Loop Impedance Meter Overview

    The MZC-305 meter is a modern, easy to use, safe measuring device used to make measurements which help determine the electrical installation safety level. These test help verify if a fault occurs in an electrical installation that enough current will flow to operate the circuit breaker or fuse protecting the faulty circuit in adequate time predetermined time.

    Features of Short Circuit Loop Impedance Meter

    • Loop impedance measurement resolution 0,01 Ω
    • Loop impedance measurement without tripping the circuit breaker > 30 mA with resolution 0,01 Ω (100...440 V)
    • Measurements possible in installations 110/190 V, 115/200 V, 127/220 V, 220/380V, 230/400 V, 240/415 V, 290/500 V and 400/690 V (range 100...750 V)
    • Short circuit current indication
    • Voltage measurement up to 750 V and up to 250 V with resolution 0,1 V
    • Measurements using Uni-Schuko adapter or test wires 1,2; 5; 10 and 20 m
    • Memory of 990 records
    • USB connection with PC
    • Powered by disposable or rechargeable (4xAA)
  • Multi-function Electrical Installation Meter | MPI-540

    Call for price

    MPI-540 Multi-function Electrical Installation Meter Overview

    The MPI-540 meter is designed for checking home and industrial electrical installations. Measurements taken by this device, provides results to determine the safety of the installation. The user also has the possibility to register the parameters of electrical networks location at these facilities.

    This allows verification of the quality of electricity, and measurement of the parameters of protection against electric shock using a single universal device. This superior meter combines the measurement capabilities of several devices, while ensuring equally and accuracy. Significant automation of measurements with the meter makes it possible to test functioning of residual current circuit breaker in the auto mode, as well as in pre-programmed measuring sequences (so called auto-tests), which can also be extended with own sequences. Automatic measurement of insulation resistance of 3-, 4- and 5- wire conductors is possible by using additional the AUTO ISO-1000C adaptor.

    This device is ideal for all measurements for commissioning of electrical installations in accordance with applicable regulations:

    Features of MPI-540 Multi-function Electrical Installation Meter

    • 7 " TFT LCD touch screen with a resolution of 800 x 480 pixels
    • removable memory card - easy increase of memory capacity
    • One device can be used for all measurements for commissioning of electrical installations in accordance with applicable regulations:
      • short circuit loop impedance (also in circuits with RCDs)
      • parameters of RCDs
      • insulation resistance
      • earthing resistance (4 measurement methods + ground resistivity measurement)
      • continuity of protective and equipotential bondings
      • lighting measurement
      • phase sequence tester
      • motor rotation direction tester
    • three-phase power network data logger, can record 50/60 Hz power network parameters in acc. to S class of EN 61000-4-30:
      • voltage L1, L2, L3, - average values in the range up to 500 V,
      • L1, L2, L3 currents, - average values, current measurement in the range up to 3 kA (depending on the current clamps used)
      • frequency in the range of 40Hz - 70Hz
      • active (P), reactive (Q) and apparent (S) power
      • power factor (PF), cosφ
      • harmonics (up to 40 in voltage and current)
      • total harmonic distortion (THD) for current and voltage
  • Mili Ohmmeter

    Cropico DO4000 MilliOhm Meter

    Call for price

    DO4000 Milliohm Meter

    This portable milliohm meter is a practical digital instrument measuring low resistance, ideal for use in multiple industries workshop, field or test labs in Aerospace, Automotive, n Manufacturing, Military, Utilities - electrical, water and gas.

    This milliohm meter is of rugged construction contained in a sturdy plastic case with easy to use buttons. The Series 4000 has many advanced features, including auto ranging, forward and reverse current measurement with auto average, true current zero, protection up to 415 volts rms, digital calibration and long scale length, 4000 count and auto power down to maximise battery life.

    The Series 4000 milliohm meters are supplied ready for immediate use with batteries and measuring leads, no extras are normally necessary.

    DO4000 MiliOhm meter features

    • True 4 terminal Kelvin/Thomson principle measurement eliminates lead resistance errors
    • True zero capabilities Buttons to null measurement offsets
    • Digital calibration
    • Open circuit lead warning on display
    • 15mm LCD 4000 count with automatic decimal point and polarity indication
    • Manual Auto Ranging selection
    • Calibration Digital security key protected
    • Removable pack with 5 1.5V non-rechargeable batteries.
    • Separate rechargeable pack, charger and docking station as optional extras
    • Safety EN 61010-1 EMC-EN 61236
    • Forward and Reverse current measurement with auto Averaging to compensate for thermoelectric effect
  • Mili Ohmmeter

    Cropico DO4A Milli-Ohmmeters

    Call for price

    This portable digital ohmmeter is a practical instrument for low resistance measurement, ideal for use in the workshop, field or test facilities. It is of rugged construction contained in an aluminium case with tilt handle.

    The DO4A has many advanced features, including protection up to 415 volts rms, digital calibration and long scale length, 4,000 count. The rechargeable sealed lead acid battery means real portability with more than 14 hours continuous operation, without the problems normally associated with other battery types. Full measurement capability is maintained whilst charging.

     

  • Micro ohmmeter

    Cropico DO7 Micro-Ohmmeter

    Call for price

    Micro Ohmmeter DO7

    The DO7 digital micro ohmmeter is a practical instrument for low resistance measurement, ideal for utilities use in the workshop, field or test facilities. It is of rugged construction, contained in a sealed ABS plastic case with lid and carrying handle.

    The DO7 digital micro ohmmeter has many advanced features. Rechargeable batteries means real portability with more than 1 hour of continuous operation on the lowest ranges(10A), and 20 hours on all others. The internal charger will boost charge to 90% of full charge, switching automatically to a trickle maintenance charge. Warning LEDs illuminate when an open circuit lead condition is detected.

    Micro Ohmmeter Features DO7:

    • True 4 terminal measurement eliminates lead resistance errors
    • 10A measuring current
    • Rechargeable batteries with built-in charger
    • Measuring ranges 600µΩ to 60Ω
    • Resolution 0.1µΩ on 600µΩ range
    •  0.8” LED display daylight viewable
    • Auto average of forward and reverse measurement
    • Remote start socket
    • All solid state design
    • Wide range of leads and accessories available
    • RS232 printer output
    • Protection up to 415Vrms at the measuring terminals,
    • Digital calibration and long scale length
    • 6,000 count