Tag: Fitters

Home -> Tag: Fitters

Fitters

Time Domain Reflectometer | TDR-410
R28,542.00 ex vat

Time Domain Reflectometer - Overview

TDR-410 time-domain reflectometers are designed to detect the location of faults in metal wires. These products are designed for electrical wholesalers, cable dealers, electrical installation companies, maintenance personnel at manufacturing plants and building personnel.

SONEL reflectometers are known for their long range, up to 4,000 m for the TDR-410, very low margin of 1% error in measurement, and the ability to adjust both the velocity of propagation and the impedance of the cable which is under investigation. Two cursors indicate the distance to 2 faults and the distance between them.

Cable fault location Includes:
- Locate damaged power cables
- Fault location for copper telecom cables
- Coaxial cable fault location
- Fault location for wiring infrastructure
- Detection of breaks, short circuits and damage
- Graphic depiction of damage to cable
- Automatic indication of the distance to fault
Time Domain Reflectometer - Features:
- Automatic or manual mode:
  - Automatic fault location (AFL)
  - Manual range selection and sensitivity
  - Scan continuous or single measurement
- Ranges from 7 m to 4000 m
- "Dead zone" measure limited to 0.5 m
- Backlit 2.5 " LCD screen
- Scan automatically or manually trigger
- Manually or automatically adjust sensitivity
- Impedance matching
- Propagation coefficient adjustment 1% to 99%
- Water-resistant housing
- Small size and weight
- Extended battery life of 30 hours
Add to basket
Short-Circuit Loop Impedance Meter MZC-20E
R8,800.00 ex vat

Short-Circuit Loop Impedance Meter - Overview

The meter has been designed for fitters and measurement technicians performing services in residential buildings, office blocks, manufacturing plants and any facilities possessing a low-voltage electrical system. The instrument is also recommended for electrical maintenance personnel.

Short Circuit Loop Impedance Meter - Features
- power supply LR6 alkaline batteries or NiMH rechargeable AA batteries (4 pcs.)
- dimensions 220 x 98 x 58 mm
- instrument weight incl. batteries 509g
- storage temperature -20...+70 C^o - working temperature -10...+50 C^o
- humidity 20...80%
- reference temperature +23 ± 2 C^o
- reference humidity 40...60%
- altitude < 2000m
- Auto-OFF time max. 900 sec.
- number of Z measurement (for rechargeable batteries) >5000 (2 measurement/minute)
- display LCD segment
- type of insulation double, according to EN 61010-1 and IEC 61557
- measurement category III 300 V according to EN 61010-1
- protection class acc. to EN 60529 IP67
- quality standard developed, designed and manufactured acc. to ISO 9001
- the instrument is compliant with the requirements of IEC 61557
- the instrument complies with PN-EN 61326-1:2006 and EN 61326-2-2:2006
Add to basket
4
Multi-function Electrical Installation Meter | MPI-540
Price range: R64,493.00 through R106,648.00 ex vat
Multi-function Electrical Installation Meter - Overview

The MPI-540 meter has models for home and industrial electrical installations, photovoltaic installations and vehicle charging stations. Measurements taken by these devices determine the safety of the installation. The user also has the option to register the parameters of the electrical network's location.

Verification of the quality of electricity and measurement of the parameters that protect against electric shock is easy with this single, universal device. This superior meter combines the measurement capabilities of several devices while ensuring quality and accuracy. Significant automation of measurements with the meter makes it possible to test functioning of residual current circuit breaker in the auto mode, as well as in pre-programmed measuring sequences (so-called auto-tests), which can also be extended with your own sequences. Automatic measurement of insulation resistance of 3-, 4- and 5- wire conductors is possible by using additional the AUTO ISO-1000C adaptor.

This device is ideal for all measurements for the commissioning of electrical installations in accordance with applicable regulations.

Multi-function Electrical Installation Meter - Features
- 7 " TFT LCD touch screen with a resolution of 800 x 480 pixels
- Removable memory card - easy increase of memory capacity
- One device can be used for all measurements for commissioning of electrical installations in accordance with applicable regulations:
  - short circuit loop impedance (also in circuits with RCDs)
  - parameters of RCDs
  - insulation resistance
  - earthing resistance (4 measurement methods + ground resistivity measurement)
  - continuity of protective and equipotential bondings
  - lighting measurement
  - phase sequence tester
  - motor rotation direction tester
- three-phase power network data logger can record 50/60 Hz power network parameters in acc. to S class of EN 61000-4-30:
  - voltage L1, L2, L3, - average values in the range up to 500 V,
  - L1, L2, L3 currents, - average values, current measurement in the range up to 3 kA (depending on the current clamps used)
  - frequency in the range of 40Hz - 70Hz
  - active (P), reactive (Q) and apparent (S) power
  - power factor (PF), cosφ
  - harmonics (up to 40 in voltage and current)
  - total harmonic distortion (THD) for current and voltage
https://www.youtube.com/watch?v=y6kt_aElw58

CONTACT US FOR MORE OPTIONS

Select options
3
Digital Clamp-on Multimeter | CMP-2000
R4,776.00 ex vat

Digital Clamp-on Multimeter - Overview

Universal clamp meter, enabling the measurement of current up to 2000 A, with the diameter of the clamp as 57 mm, and bus bar to 70 * 18 mm. The instrument has electronic overload protection for all functions and ranges.

Digital Clamp-on Multimeter - Features
- Safe, insulated measuring clamp
- Auto-ranging with over range indication
- "DATA HOLD” function, for holding measured values
- Backlit LCD
- "MAX/MIN” function
- "AUTO-OFF” function after 30 min
- "DC ZERO” possibility to zero the display & reading relative actual value less stored "zero” value
- AC/DC current measurement (TRUE RMS) up to 1500 A and DC up to 2000 A
- Measurement INRUSH current in start-up phase of electrical device
- AC voltage measurement (TRUE RMS) up to 750 V and DC up to 1000 V
- Resistance measurement and continuity test with acoustic signalling (beeper) for resistance below 30 Ω
- Capacitance measurement
- Temperature measurement
- Frequency measurement
- Duty cycle measurement
- Diode test
- Continuity test with acoustic signalling (beeper) for resistance below 30 Ω
Add to basket
AC Voltage Detector Pen | VT-2
R489.00 ex vat

Voltage Detection Pens

This easy use Non-contact AC Voltage tester. Just touch the tip to a terminal strip, outlet, or supply cord and the tip glows red and the unit beeps. This makes it easy to know whether there is voltage present. Electricians, maintenance, service, safety, personnel, and homeowners can quickly test for energised circuits in the workplace or at home.

Voltage Detection Pen Features:
- Rugged, double moulded case
- Non-Contact Detection of AC Voltage from 90 VAC to 1000 VAC
- Suitable for outlets or against wire insulation testing
- Flashing red LED light indicator
- Audible beeper indicator
- Built-in bright flashlight with ON/OFF button
- Convenient size with pocket clip
- For use on 50/60 Hz circuits
- Supply by 2 x 1,5 V batteries (LR03)
Add to basket
Wire and Pipe Locator | LKZ-720
R24,293.00 ex vat

Wire and Pipe Locator - Overview

Detect and trace cables in ceilings, walls and floors with the LKO-720. The specially designed 3D antenna allows for precise wire tracing as well as making it easy to establish the direction of wires in concrete up to 5 cm. Locate power points and switches in buildings, the location of fuses, and trace insulated conductors. Non-contact detection of live cables allows for precise detection of energised wires in the air and concrete without additional probes.

Wire and Pipe Locator - Features
- Detects cables in ceilings, walls and floors
- Detects breaks in cables
- Traces cables in building installation
- Locates power points and switches in buildings
- Locates short circuits between leads
- Traces shielded cables
- Traces cables in metal ducts
- Identifies fuses on the distribution board
- Traces underground cables
- Traces conductive water and heating pipelines
- Non-contact detection of live cables
- 3D function in the receiver - detects direction of current flow
- Phase detection mode
- Receiver operation with four transmitters
- LED bright torch
- Headphone socket in receiver
- Screens backlit for work in dark
- Transmission of battery status and settings to the receiver
- Operation in wide range of rated voltage, up to 500V RMS
- Measurement of voltage up to 500 Vrms
- Three levels of transmitter amplification
- Automatic or manual selection of transmitter operation modes
- 5 modes of wire tracer operation - voltage, current, current-voltage, power & clamp
- Software upgrade via USB
- Additional accessories enable precise localisation
https://www.youtube.com/playlist?list=PLICwL6VglKz1POiL3V8rbq2nigFhdVFWw

Select options
1
Electrical Installation Meter with Power Analyzer | MPI-540

Electrical Installation Meter - Overview

The MPI-540 meter is designed for checking the safety of industrial and domestic electrical installations. The user has the option to register the parameters of electrical networks located at these facilities. This allows for the measurement of the parameters for protection against electric shock using a single universal device while verifying the quality of electricity. The Auto mode allows significant automation of measurements of the meter and makes it possible to test the functioning of residual current circuit breakers, as well as in pre-programmed measuring sequences, which can be extended with their own sequences. Automatic measurement of insulation resistance of 3-, 4- and 5-wire conductors is possible by using an additional AUTO ISO-1000C adapter.

Read more
Light Meter | LXP-10B
R15,192.00 ex vat
Light Meter - Overview

The LXP-10B digital light meter allows for a very precise measurement of illuminace. Thanks to very high resolution (resolution 0.01 lx), it is suitable for accurate lighting measurement in the workplace and emergency lighting in escape routes. It works in conjunction with the LP-10B measuring probe. The device has an internal memory of 999 measurements and an additional logger for recording data with a selectable sampling rate.

Light Meter - Features
high resolution up to 0.01 lx

highly accurate

measurements of all types of light sources:

LEDs lamps

incandescent lamps

fluorescent lamps

electrodeless lamps

high and low-pressure lamps

no need to use correction factors

photodiodes with filters match the spectral sensitivity characteristics well to the requirements of C.I.E.

data-hold for freezing measuring values

automatic zeroing

peak-hold for freezing the peak signal of light pulse

capable of selecting measuring mode in Lux / FC scale

MAX and MIN results save

relative mode

easy to read large backlit display

USB connection with PC

wireless connection

built-in memory: 999 points

16 000 values records data logger

auto power off
https://www.youtube.com/watch?v=z4Lkfnx5qc0

Add to basket
Hand-held Multiprobe Anemometer | MiniAir20

Hand-held Multiprobe Anemometer - Overview

Hand-held measuring instruments to measure flow velocity of gaseous and liquid media, relative humidity and temperature. It features high precision and robustness and is especially suitable for mobile and laboratory applications.

Hand-held Multiprobe Anemometer - Features
- Very simple operation, hand keyboard
- Easy to repair on site thanks to the snap-on head principle
- Momentary value measurement
- All three channels can be displayed simultaneously
- IR interface for on-site report printer
- Accuracy: +1.0 % f.e. +1.5% f.m. (for MiniAir20 Mini)
- Automatic sensor detection
- Interval measurement
- Average, minimum and maximum values can be displayed simultaneously
- Storage on microSD card
- Battery operation, mains operation possible
Read more
Thermal Imager | KT-670

Thermal Imager - Overview

This fully radiometric, high-resolution camera records temperature at each point of the image. It makes shooting professional IR images fast and easy. It is compact, lightweight, durable, and water and dustproof. Casing IP54 rating. Other features include a compass, GPS, IR analysing functions, and Wi-Fi reports printing. Including free intuitive software for image editing and report creating.

Thermal Imager - Features
- WiFi & Bluetooth wireless communication
- Multiple image presentations including IR visible, PIP and IR blending
- High resolution IR images up to 120.000 pixel (400x) and 307,200 pixels (640x480) alternative
- Visible light digital camera 5MP resolution with LED lamp provides sharp images
- 5-inch 720P high-resolution LCD touch screen for better image clarity and easy operation
- Rotating LCD display up to 270" for easy viewing angle
- Rotating lens pivots up to 70" for easy viewing angle
- 4x (or 10x for plus version) continuous zoom with auto/motorized focus
- Android-based operation system with open platform for various APP developments and convenient program upgrades
- Powerful onboard analysis and reporting capabilities
- Optional high-temperature range measuring up to 2000^oC (3632^oF) targeting electrical and industrial applications
- Optional 11 telephoto or 45 wide angle lens
Read more
1
Short Circuit Loop Impedance Meter MZC-305

Short Circuit Loop Impedance Meter - Overview

The MZC-305 meter is a modern, easy-to-use, safety measuring device. It is used to make measurements which help determine the electrical installation safety level. These tests help verify that if a fault occurs in an electrical installation, enough current will flow to operate the circuit breaker or fuse protecting the faulty circuit in the adequate, predetermined time.

Short Circuit Loop Impedance Meter - Features
- Loop impedance measurement resolution 0,01 Ω
- Loop impedance measurement without tripping the circuit breaker > 30 mA with resolution 0,01 Ω (100...440 V)
- Measurements possible in installations 110/190 V, 115/200 V, 127/220 V, 220/380V, 230/400 V, 240/415 V, 290/500 V and 400/690 V (range 100...750 V)
- Short circuit current indication
- Voltage measurement up to 750 V and up to 250 V with resolution 0,1 V
- Measurements using Uni-Schuko adapter or test wires 1,2; 5; 10 and 20 m
- Memory of 990 records
- USB connection with PC
- Powered by disposable or rechargeable (4xAA)
Read more